-
- دوشنبه تا شنبه: 10:00 - 16:00 / یکشنبه تعطیل است
The unbalance of the cone crusher rotor will cause excessive vibration of the equipment body, aggravate the friction between the parts, and then cause the cone crusher body to heat up. 4. The amount of lubricating oil added to the equipment is inappropriate.
به خواندن ادامه دهید
Conical Mounts. Conical mounts also known as cone mounts isolate shock, motion and vibration in all planes (x,y,z) and if necessary with different loads in each direction to ensure the optimum isolation throughout a wide range of frequencies. Conical mounts have a high load carrying capacity within a compact size that assures a stable solution and are designed with an outer and inner metal sleeve.
به خواندن ادامه دهید
6. Strong vibration of cone crusher. The reason. The device base fixture may be loose. There are hard-to-crush materials in the crushing cavity of the cone crusher. Too much material in the crushing cavity causes blockage. The liner is broken or worn. Poor lubrication causes the spindle to be wrapped tightly by the bushing. Solution
به خواندن ادامه دهید
Multi-cylinder hydraulic cone crushers are widely used in the sand aggregate and mining industries, especially in the medium and fine crushing processing systems of medium-hard materials. We introduce 4 common problems in the operation of cone crusher: abnormal vibration, high noise, easy dirty lubricating oil, high oil return temperature, and introduce how to solve them.
به خواندن ادامه دهید
The main reason of ＂flying car＂ failure of cone crusher . Dynamic cone part of cone crusher in the process of production at a certain speed do periodic rotating pendulum movement, but often because of some special reasons, there will be a dynamic cone speed suddenly increase, the body's sudden severe vibration, insurance spring or cylinder in abnormal working state, the working current ...
به خواندن ادامه دهید
The oil temperature is too high. 2. Oil temperature and pressure rise. 3.Oil pressure is low after oil pump is started. 4.Oil contain lots of fine mud and impurities. 5.There is water in the oil. 6.The vibration of cone crusher is too strong. 7. The crushing cone rotates very high.
به خواندن ادامه دهید
Spring cone crusher. 2. Solution (1) To fundamentally eliminate the noise of the spring cone crusher, it is necessary to correctly mesh the large and small bevel gears to eliminate the reciprocating sliding and additional impact between the gears, prolong the service life of the gears and fundamentally eliminate the source of noise. .
به خواندن ادامه دهید
The project of the vibration crusher with three degrees of freedom is proposed. The degrees are limited by the guide rails that hold the crusher body and cone against horizontal and spiral motions. The mathematical model for this project is obtained. The observations for the motion of the body, the cone and the unbalance vibrator are made in a numerical experiment.
به خواندن ادامه دهید
The main reason of ＂flying car＂ failure of cone crusher . Dynamic cone part of cone crusher in the process of production at a certain speed do periodic rotating pendulum movement, but often because of some special reasons, there will be a dynamic cone speed suddenly increase, the body's sudden severe vibration, insurance spring or cylinder in abnormal working state, the working current ...
به خواندن ادامه دهید
The crusher often vibrates. 1) For spring cone breaking, when the spring tension of the crusher is not enough, the crusher will often vibrate. 2) When the feeding of the crusher is uneven or excessive, it will often cause the crusher to vibrate. 3) When there is too much fine ore in the feed of the crusher and it is wet, the ore discharge port ...
به خواندن ادامه دهید
2. When the material feeding is not uniform or too much, it will cause the crusher often vibration. 3. When the aggregates contain too much powder or too wet, due to the small discharging opening, these materials will block the discharging opening. This causes the cone crusher vibrate. Luoyang Dahua mainly produce cone crusher, impact crusher ...
به خواندن ادامه دهید
The design scheme of the shock-vibration cone crusher is shown in Figure 1. The body of the. machine 1, and also the crushing cone 3 attached to it by means of special packages of helical springs ...
به خواندن ادامه دهید
Crusher spring is not enough tightness; the ore uneven or excessive, the crusher will cause frequent vibration; When the crushed mine excessive and moisture, the out mouth is small, resulting in the port of discharge at the mine often blocked, causing frequent vibration crusher. For more information about crusher spare parts, please contact us.
به خواندن ادامه دهید
The crusher often vibrates. 1) For spring cone breaking, when the spring tension of the crusher is not enough, the crusher will often vibrate. 2) When the feeding of the crusher is uneven or excessive, it will often cause the crusher to vibrate. 3) When there is too much fine ore in the feed of the crusher and it is wet, the ore discharge port ...
به خواندن ادامه دهید
10 Things You Must Stop Doing to Your Cone Crusher . Nov. 13, 2014 ... but let it go too far and you get vibration and metal fatigue and a host of related problems that means to could be "cap ex time" when you have no capital expenditure budgeted. 4. Shock loading with feed material: yes, the machine is built to crush, but when you dump a ...
به خواندن ادامه دهید
a. not designed shock absorbing structure installed crusher or not the base cushion pad damping plate, when the crusher relatively stiff material, the sound vibration device will be larger. b. member connected properly.Into the crusher, the material should be soft pipe connection, it may also cause excessive vibration device. Back:Cone Crusher.
به خواندن ادامه دهید